dalong@dalonmachine.com

+86-13567788178

Product Categories

Contact Dalong Machinery


Address: 707#,Binhai 8th Rd., Wenzhou Eco&Tech Development Zone, Longwan District, Wenzhou, Zhejiang, China


CONTACT: Sally Young

Cell:+86 13567788178


TEL:  +86-577-86526789

FAX: +86-577-86502588


Sales Email: 

dalong@dalonmachine.com

overseasales@dalonmachine.com


Website: 

www.dalongmachinery.com

https://dalonmachine.en.alibaba.com 

 

WhatsApp:+86 13567788178

WhatsApp:+86 15869602225


Home > News > Content
Steaming Machine Boiler Oct 23, 2017

The steam engine is a reciprocating power machine that converts the energy of the steam into mechanical work. The emergence of the steam engine has caused the 18th century industrial revolution. Until the beginning of the 20th century, it was still the most important motive in the world, and later gradually let the internal combustion engine and steam turbine.

The steam engine needs a boiler that boils water to produce high-pressure steam, which can use wood, coal, oil or natural gas and even combustible waste as a heat source. Steam expansion drives the piston to work.

Steam engine mainly by the cylinder, base, piston, crank connecting rod mechanism, slide valve with steam institutions, speed control agencies and flywheels and other components. The cylinder and the base are stationary.

In a steam boiler, the water is boiled into steam by burning. Through the pipeline steam was sent to the cylinder. The valve controls the time the steam reaches the cylinder, enters the slide valve chamber through the main steam valve and the throttle valve, and enters the left or right side of the cylinder alternately by the spool valve to push the piston movement. Steam in the cylinder to push the piston work, cooling the steam through the pipeline was introduced into the condenser to re-condense into water. This process is repeated during the steam engine movement.

The general steam engine has three cylinders to form a group. The steam engine directly converts the up and down movement of the piston into the rotary motion of the axle. The new steam engine also contains a small turbine, the steam from the cylinder can also use its waste heat in the promotion of the turbine to improve the efficiency of the entire drive device. The turbine is also connected to the propeller shaft of the ship.

The biggest advantage of modern steam engines is that it can use almost all of the fuel to convert thermal energy into mechanical energy. Unlike the internal combustion engine, it is not critical of its fuel. In addition there is no steam engine, then the atomic energy can not be used. Atomic reactors do not directly produce mechanical energy, and do not directly generate electricity, the atomic reactor is actually only heated water, the water is boiling steam through the steam engine to be converted into useful work. Steam does not necessarily need to be produced by combustion, such as the use of solar heaters can also produce steam to promote the steam engine.

Another small-sized external combustion engine with similar advantages is the Stirling engine. The downside is that it is difficult to run in many cases.

In particular, the advantages of steam locomotives in the mountains are significant because they can also operate at relatively low air pressures. This will be found when South America will replace its steam locomotives with diesel-electric locomotives. In the mountains they had to give up the use of relatively high power diesel locomotives, replaced by power, but not as diesel locomotives but not by sea limit steam locomotive.

The use of modern steam engines in Swiss and Austrian new railroad rails requires only one person to run, saving 60% more fuel than the previous steamer, 50% lighter than the electric and diesel engines, The wear is much smaller. There is also a new steam engine boat on Lake Geneva, the world's first remote control steam engine.

Steam engine weakness is: can not do without the boiler, the whole device is both cumbersome and bulky; new steam pressure and temperature can not be too high, the exhaust pressure can not be too low, thermal efficiency is difficult to improve; it is a reciprocating machine, inertia limit the speed The work process is not continuous, the steam flow is limited, also limits the power of the increase.

Therefore, abandoned the bulky engine of the internal combustion engine, and ultimately its light weight, small size, high thermal efficiency and flexible operation, etc., in the ship and the locomotive gradually replaced the steam engine. Steam turbine with its high thermal efficiency, single power, high speed, light weight per unit power and smooth operation, etc., the steam engine out of the power station.

Then the motor and its easy to use, instead of the steam engine in industrial equipment applications. However, the thermal efficiency of the low-power steam engine is higher than that of the steam turbine, so the steam engine still has the room to play a role in the coal producing area or in the areas where only the inferior fuel is in the area or some special occasions.